Wipe off the top surface of the vial containing your Melanotan 2 and bottle containing the sterile water.* Take your syringe and insert it through the rubber stopper into the vial holding the water. Turn it upside down, draw out 100 units (1 cc/ml) of water, inject this into the vial of Melanotan powder.* Roll the vial gently until the Melanotan is dissolved. Do not shake. With this dilution there is 1mg of Melanotan 2 per 10 units. Your mixed vial will now contain 100 total units of Melanotan 2.
Dosage
You will begin with a "loading phase" tan injection. During this phase it is recommended that you start off with a small daily dose, such as 2 units per day (2 units= 0.2mg= 200mcg) and increase 2 units every 3 days until you are at 10 unit doses.* Remain at 10 unit daily doses until you are as dark as you would like to be.* Once dark enough, you will then begin your "maintainance phase". During this tanning injection phase you will cut back to only taking 5 to 10 units per week to maintain your tan all year round* *
""*
Injecting Melanotan 2
* 1. Always wash your hands thoroughly.
* 2. Load up the syringe.
* * * * * * Take the protective cover of the needle, top and bottom.* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * * Insert the needle into the vial through the center of the rubber stopper.
* * * * * * Turn the vial upside down with the needle still inside.
* * * * * * Pull back the plunger to the desired dosage mark* on your needle. (2 units for first time user).
* * * * * * Check your needle for any air bubbles, tap the needle so they rise to the top and then push the plunger to remove them.
* 3. Select the injection site.
* * * * * * You can inject anywhere on the body where there is a higher fatty layer.
* * * * * * Always vary the injection site.
* * * * * * Never inject any bruised, swollen or scarred areas.
* 4. Clean the injection site.
* * * * * * Clean a two-inch area of the selected site with an alcohol swab.* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* * * * * * Let the area dry.
* 5. Actual tan injection.
* * * * * * Using the hand you write with, hold the needle over the area you have cleaned.
* * * * * * With your other hand pinch two to three inches on either side of the area you have cleaned.
* * * * * * Using a quick motion, insert the needle into the pinched area. The needle should go all the way into the skin.
* * * * * * Push the needle plunger until all of the Melanotan 2 is out of the needle.
* * * * * * Quickly pull the needle out.
* * * * * * Apply gentle pressure to the site with the alcohol wipe.
* * * * * * Do not rub the injection site.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Mixing: Bacteriostatic water is used for MT-2 reconstitution
Peptide at photo left is 5MG MT-2
Example-* 2ml(cc) bacteriostatic water per 5mg MT-2 vial reconstitutes a 250mcg dose approximately every 10 units (5 tick marks) on a U100 insulin syringe.
Peptide at photo right is the standard 10MG MT-2
Example-* 2ml(cc) bacteriostatic water per 10mg MT-2 vial equates to a 500mcg dose approximately each 10 units (5 tick marks) on a U100 insulin syringe.
Reply With Quote